AD-LU 45 GT, AD-LU 45S GT

Description

The digital power converter AD-LU 45 GT measures all values of the three-phase power grid such as current, voltage, energy, active, reactive, apparent power and frequency and makes this data available via a fieldbus. The device is therefore ideally suited for integration into energy management systems. The ProfiNet variant contains a 2-port switch for direct forwarding to the next device. 3- or 4-wire networks can be measured. 4-wire networks may have balanced or unbalanced load. 3-wire networks must have balanced load. The AD-LU 45 GT is powered by its measuring voltage L1. However, a variant with separate supply terminals and wide-range power supply is also available (AD-LU 45-S GT).The current measurement takes place via external split-core current transformers, which can be mounted on the wire to be measured without cutting. For the measurement of higher voltages, external converters can be connected at any time. LEDs on the front panel signal the operating state and the data traffic. The compact design and the high performance combined with low energy consumption allow it to be used in almost any application. In addition, the device has a front-sided RS485 interface to which, for example, the TFT display AD-MM 400 can be connected. Somit können ohne großen Aufwand auch vor alle Messwerte angezeigt werden. Thus, without any great effort, all measured values can be displayed.

AD-LU 45 GT,  AD-LU 45S GT

Application

Measurement and monitoring of all electrical characteristics in electrical systems. Detection of load profiles for energy management systems, e.g. ISO 50001. Recording the energy consumption of individual consumers. Monitoring of voltage quality variables, e.g. Harmonics.
Attention: This is a Class A product according to EN 55011. Additional EMC actions may be necessary when used in small businesses or in residential areas.

Specific characteristics

  • Measurement of currents, voltages, power, power factors, frequency, harmonics
  • Connection to external spli-core transformers
  • Counters for aktive, reactive and apparent energy
  • Fieldbus interface for PROFINET or PROFIBUS
  • RS485 interface for connecting a TFT display

Business data

Order number
AD-LU 45 GT-PN PROFINET
AD-LU 45-S GT-PN PROFINET, with separate supply terminals
AD-LU 45 GT-PB PROFIBUS
AD-LU 45-S GT-PB PROFIBUS, with separate supply terminals
Accessory
AD-KSW 50/100/200/400/600 Split core current transformer 50/100/200/400/600 A
AD-MM 400 TFT display for front panel installation
Identifiers
EClass 27210124
Customs tariff number / country of origin 8543 70 90 / Deutschland

Information

Downloads
Data sheet pdf en-lu45gt.pdf (415 kB)
PROFINET / PROFIBUS Datei zip AD-LU45GT-GSx.zip
Tender text zip lu45gt.zip (15 kB)
Tender text zip lu45-sgt.zip (16 kB)
STEP file zip lu45gt.zip (523 kB)
Safety instructions pdf ad-safety-instructions.pdf (43 kB)

Technical specifications

Current-inputs (I1...I3)
Measuring ranges 0 ... 33,3 mA (over split-core-transformer)
Input resistance Ca. 10 Ohm
Max. measurable harmonic 40
Voltage-inputs (L1...L3)
Measuring range 80 ... 253 V AC (AD-LU 40 GT)
0 ... 253 V AC (AD-LU 40S GT)
Input resistance Ca. 970 kOhm
PROFINET
Ethernet 2 Port Switch
Protocol specification PROFINET IO
Default IP-address 0.0.0.0
PROFIBUS
Address setting BCD-switches 00...99
Bus termination 120 ohms both sides at the end
Max. length of bus 500 m (no stubs)
Cable Twisted and shielded
RS485-Bus
Software protocol Modbus-RTU
Data format 19200, e, 8, 1
Max. bus users 99
Bus termination 120 ohms both sides at the end
Bus termination 120 ohms both sides at the end
Max. length of bus 500 m (no spur lines)
Cable Twisted and shielded
Address setting BCD-switches 00...99
Supply
Voltage range AC 80 ... 253 V AC, 50/60 Hz (see voltage-inputs)
Nominal voltage AC 230 V AC
Power consumption Max. 4 VA
Supply (-S)
Voltage range AC 50 ... 253 V AC, 50/60 Hz
Voltage range DC 20 ... 253 V DC
Nominal voltage AC/DC 230 V AC / 24 V DC
Input power AC/DC Max. 4 VA / 3 W
Measure
Basic accuracy <= 0,5 % (class 0.5)
Temperature influence 80 ppm/K
Sampling interval 200 ms
Housing
Dimensions (WxHxD) 105x90x71 mm
Type of protection IP 20
Connection method Screw clamp
Terminals, wire cross section 2,5 mm² flex wire / 4 mm² one wire
Bolting torque terminals 0,6 Nm
Weight ~ 210 g
Manner of fastening 35 mm DIN rail 35mm
Environmental conditions
Ambient temperature -10 ... 50 °C
Storage and transport -10 ... 70 °C (no condensation)
EMC
Product family standard EN 61326-1 1)
Emitted interference EN 55011, CISPR11 Cl. A, Gr. 1
Electrical safety requirements
Product family standard EN 61010-1
Overvoltage category II
Pollution degree 2
Safety measurement EN 61010-2-030
Measurement category CAT III
Galvanic isolation, test voltages
Grid side zu bus 4 kV, 50 Hz (1 min.)
Grid side to control elements 4 kV, 50 Hz (1 min.)
1) During checking, slight signal deviations are possible.

Block and wiring diagram

AD-LU 45 GT,  AD-LU 45S GT

Dimensions

AD-LU 45 GT,  AD-LU 45S GT

Circuit examples

AD-LU 45 GT,  AD-LU 45S GT

We only use technically necessary cookies to improve the user-friendliness of our site.
Cookies for analysis and marketing purposes are not used!
You can find further information in our privacy policy.
made with ♡ by andres.media