!Vorlage

Description

CAUTION Template - DO NOT save as a new device.

Application

# For more options and information see # http://rpf.io/configtxtreadme # Some settings may impact device functionality. See link above for details #https://www.dinotools.de/2015/03/14/monitor-beim-raspberry-pi-drehen/ #display_rotate = 2 # uncomment if you get no picture on HDMI for a default "safe" mode #hdmi_safe=1 # uncomment this if your display has a black border of unused pixels visible # and your display can output without overscan #disable_overscan=1 # uncomment the following to adjust overscan. Use positive numbers if console # goes off screen, and negative if there is too much border #overscan_left=16 #overscan_right=16 #overscan_top=16 #overscan_bottom=16 # uncomment to force a console size. By default it will be display's size minus # overscan. #framebuffer_width=1280 #framebuffer_height=720 # uncomment if hdmi display is not detected and composite is being output #hdmi_force_hotplug=1 # uncomment to force a specific HDMI mode (this will force VGA) #hdmi_group=1 #hdmi_mode=1 hdmi_group=2 hdmi_mode=16 # uncomment to force a HDMI mode rather than DVI. This can make audio work in # DMT (computer monitor) modes #hdmi_drive=2 # uncomment to increase signal to HDMI, if you have interference, blanking, or # no display #config_hdmi_boost=4 # uncomment for composite PAL #sdtv_mode=2 #uncomment to overclock the arm. 700 MHz is the default. #arm_freq=800 # Uncomment some or all of these to enable the optional hardware interfaces #dtparam=i2c_arm=on #dtparam=i2s=on #dtparam=spi=on # Uncomment this to enable the lirc-rpi module #dtoverlay=lirc-rpi # Additional overlays and parameters are documented /boot/overlays/README # Enable audio (loads snd_bcm2835) dtparam=audio=on # NOOBS Auto-generated Settings: hdmi_force_hotplug=1 avoid_warnings=1 ## emoves the warning overlay. #avoid_warnings=2 ## additionally allows turbo when low-voltage is present. hdmi_blanking=1

Business data

Order number
Template GV
Vorlage GVC	Test

Information

Downloads
	aab20gx.pdf (223 kB)
Safety instructions	ad-safety-instructions.pdf (43 kB)

Technical specifications

Input current
Measuring range	0 ... 20 mA
Input resistance	50 Ohm
Resolution	10 Bit
Input voltage
Measuring range	0 ... 10 V
Input resistance	100 kOhm
Resolution	10 Bit
Output current
Output range	0 ... 20 mA
Max. burden	500 Ohm
Residual ripple	20 µAss
Resolution	11 Bit
Output voltage
Output range	0 ... 10 V
Min. burden	10 kOhm
Residual ripple	10 mVss
Resolution	11 Bit
Relay output
Maximum switching load AC	250 V, 2 A
Maximum switching load DC	50 V, 2 A
Contact construction	Closing contact
Switching operations mechanical	10000000
At 230V/2A AC, cos(phi)=1	600000
At 230V/2A AC, cos(phi)=0,4	200000
At 24V/1 A DC	200000
Supply
Voltage range AC	50 ... 253 V AC, 50/60 Hz
Nominal voltage AC	230 V AC
Voltage range DC	20 ... 253 V DC
Nominal voltage DC	24 V DC
Power consumption AC / DC	2 VA / 1W
Transmission behaviour
Basic accuracy	< 0,2 %
Temperature influence	100 ppm/K
Response time	~ 20 ms
Housing
Dimensions (WxHxD)	13x110x124 mm
Type of protection	IP 20
Connection method	Detachable terminal clamp
Terminals, wire cross section	2,5 mm² flex wire / 4 mm² one wire
Bolting torque terminals	0,5 Nm
Weight	~ 100 g
Manner of fastening	35 mm DIN rail 35mm
Environmental conditions
Ambient temperature	-10 ... 50 °C
Storage and transport	-10 ... 70 °C (no condensation)
EMC
Product family standard	EN 61326-1 ¹⁾
Emitted interference	EN 55011, CISPR11 Cl. B, Gr. 1
Electrical safety requirements
Product family standard	EN 61010-1
Overvoltage category	II
Elevation	Max. 2000 m
Pollution degree	2
Safety measurement (only AC)	61010-2-030
Measurement category	CAT III (nur AC)
Max. permanent working voltage	300 VAC
Functional safety
Safety integrity level	SIL 2, IEC 61508
Galvanic isolation, Working voltages ²⁾
Input / output	250 V DC or ACeff
Input / supply unit	300 V DC or ACeff
Output / supply unit	300 V DC or ACeff
Galvanic isolation, test voltages
Input / output	2,5 kV, 50 Hz (1 min.)
Input / supply unit	3 kV, 50 Hz (1 min.)
Output / supply unit	3 kV, 50 Hz (1 min.)
Protection circuits
Input	Electrical surge protection
Output	Electrical surge protection
Power supply	Electrical surge and reverse current protection

¹⁾ During checking, slight signal deviations are possible.
²⁾Maximum voltage permanently across the insulation.

Block and wiring diagram

!Vorlage

Dimensions

!Vorlage

Circuit examples

!Vorlage

CAD / CAE Daten

CAD model is not yet available for this product.

The CAD product overview can be found at: adamczewski.partcommunity.com